Printing Process

How to Screen Print T-Shirts: A Step-by-Step Guide

Learn how to screen print T-shirts at home or in a small shop: artwork, film, emulsion, exposure, printing, curing and cleanup, explained step by step.

On this page
  1. Screen printing in seven steps
  2. What you need to get started
  3. Step 1: Prepare the artwork and film positives
  4. Step 2: Coat the screen with emulsion
  5. Step 3: Expose the screen
  6. Step 4: Wash out, dry and inspect the stencil
  7. Step 5: Set up the press and register the screen
  8. Step 6: Print the shirt
  9. Step 7: Cure the ink
  10. Step 8: Clean up and reclaim the screen
  11. Going further: dark shirts, multiple colors and full-color artwork
  12. Tips that save reprints
  13. Caring for screen-printed shirts
  14. Is screen printing the right method for your job?

Screen printing in seven steps

Screen printing pushes ink through a stencil on a mesh screen onto a shirt. Each color in a design needs its own screen, so a one-color design is the simplest place to start. The basic workflow is the same whether you are printing at a kitchen table or in a small shop:

  1. Prepare the artwork and output it as a film positive.
  2. Coat a clean screen with photo emulsion and let it dry in the dark.
  3. Expose the screen to light through the film.
  4. Wash out the stencil and let the screen dry.
  5. Set up the screen on a press and position the shirt.
  6. Print by flooding and pulling ink across the screen with a squeegee.
  7. Cure the ink with heat so it bonds to the fabric.

Afterward you clean the screen and, when you no longer need the stencil, reclaim it for the next design. The sections below cover each step and point to deeper guides where a step needs more detail.

What you need to get started

Exact kits vary, but a basic photo-emulsion setup usually includes:

  • Screens: a mesh stretched on an aluminum or wood frame. For general T-shirt work, many printers use a mesh count somewhere in the 110 to 160 range; finer detail generally calls for a higher count.
  • Photo emulsion and sensitizer (some emulsions come pre-sensitized), plus a scoop coater.
  • Film positives of your artwork, and a way to print them.
  • A light source to expose the screens. An exposure unit is ideal, but see how to expose a screen without an exposure unit if you are on a budget.
  • A place to wash out screens with a hose, sink or washout booth.
  • A press or a simple hinged frame setup, a flat platen or board to hold the shirt, and pallet adhesive or a similar way to keep the shirt from shifting.
  • Squeegees sized a little narrower than the inside of the screen but wider than the design.
  • Ink, usually plastisol or water-based, and the means to cure it: a conveyor dryer, flash dryer or heat press. Plastisol is commonly cured at about 320°F (160°C) throughout the ink layer, but follow the data sheet for your ink.
  • Cleanup and reclaim supplies: ink cleaner, emulsion remover, a degreaser and gloves.

You also need a dim, UV-free workspace for coating and drying screens, and good ventilation anywhere you handle chemicals or cure ink.

Step 1: Prepare the artwork and film positives

Good prints start with good artwork. Screen printing works best with bold shapes and a limited number of colors, so simplify designs where you can.

  • Work at the final print size. A full-front design is often roughly 10 to 12 inches wide, and a left-chest logo is often around 3 to 4 inches, but let the garment and the design decide.
  • Use vector art or raster files at a minimum of 300 dpi at final size, and convert text to outlines.
  • Separate each color onto its own layer. Each separation becomes one black-only film and one screen.
  • Add registration marks if you are printing more than one color.

Each separation is then printed in solid, dense black on film or transparency material. The black needs to block UV light well, so a faint or streaky print will cause trouble later. The details are in our guide to making film positives for screen printing.

Step 2: Coat the screen with emulsion

The screen must be clean, degreased and fully dry. Then, in a dim room with no UV light (yellow safelights are common), you coat a thin, even layer of emulsion on the mesh with a scoop coater. Many printers coat the shirt side first and then the squeegee side, and some add a second coat on one side, but your emulsion’s instructions and your mesh should guide the exact approach.

The coated screen then dries flat, in the dark, ideally in a warm, low-humidity, dust-free place. Rushing this step is a common cause of stencils that break down. For the full technique, including how to fix streaks, see how to coat a screen with emulsion evenly.

Step 3: Expose the screen

Once the emulsion is dry, you place the film positive against the screen’s shirt side, make sure the film is in firm contact, and expose the screen to a UV-rich light source. Light hardens the emulsion everywhere it can reach. The black areas of the film block light, so the emulsion under them stays soft and washes away.

Exposure time depends on your light, your emulsion, the coating thickness and your mesh, so there is no universal number. Run a test with an exposure calculator or a step-wedge strip to find the right time for your setup. We cover that in how long to expose screen printing emulsion.

Step 4: Wash out, dry and inspect the stencil

After exposure, wet both sides of the screen with cool water and spray the image area until the soft emulsion rinses away and the design appears as open mesh. Moderate water pressure works best; too much can damage fine detail, and too little can leave a haze in the open areas.

Then:

  • Dry the screen completely.
  • Hold it up to a light and look for hazy spots in the design areas or pinholes outside them.
  • Block any pinholes with screen filler or a dab of emulsion, and tape the edges of the screen where the mesh meets the frame so ink cannot get under it.
  • Some printers do a post-exposure under the light to harden the stencil further, which can help with durability.

Step 5: Set up the press and register the screen

Mount the screen in the press or hinge clamps. Apply a thin layer of pallet adhesive to the platen, then smooth the shirt on it without wrinkles. Set the off-contact distance, the small gap between the mesh and the shirt that lets the screen peel away from the ink after each stroke. A gap of about the thickness of a nickel, or roughly 1/8 inch, is a common starting point, but the best setting varies with your press and mesh.

For a single-color job, position the screen so the design lands where you want it. For a multi-color job, each screen must line up with the previous one, which is covered in how to register multi-color screen prints.

Step 6: Print the shirt

  1. Put a line of ink at the top of the screen, beyond the design.
  2. With the screen raised slightly, flood the screen by pulling the ink across the design with light pressure. This fills the open mesh.
  3. Lower the screen and print by pulling the squeegee back across with firm, even pressure at a consistent angle. Many printers start around 45 degrees and adjust from there.
  4. Lift the screen, check the print, and remove the shirt.

Print a test on scrap fabric first. Use the sharp edge of the squeegee, keep your pressure and speed steady, and do not overload the screen with ink. If the print looks thin, patchy or blurry, the guide to screen printing defects and how to fix them can help you track down the cause.

Step 7: Cure the ink

Printed ink is not durable until it is cured. For plastisol, that generally means bringing the ink film to about 320°F (160°C) and holding it there for the time the ink maker recommends. Water-based inks need to dry out and then cure, and the instructions vary by product. Two ways to check:

  • Measure the ink or garment temperature with an infrared thermometer or a probe.
  • Stretch and wash-test a sample. If the print cracks or washes out, it likely needs more heat or time.

Under-cured prints are among the most common reasons a shirt looks fine on day one but fails in the wash.

Step 8: Clean up and reclaim the screen

Remove excess ink right away, then clean the screen with an ink cleaner. If you are done with the design, strip the emulsion, rinse, and degrease the screen so it can be recoated. Our guide to reclaiming a screen walks through ink removal, emulsion stripping and ghost images.

Going further: dark shirts, multiple colors and full-color artwork

Tips that save reprints

  • Test everything on scrap fabric before using real shirts.
  • Keep a log of your exposure time, mesh, ink and cure settings once you find a combination that works.
  • Use a lint roller on shirts before printing to remove loose fibers.
  • Print on soft, reasonably smooth garments when you can, since the blank affects both print quality and feel.

For a longer list, see tricks for screen printing.

Caring for screen-printed shirts

A properly cured print should last through many washes, but care helps. Washing printed shirts inside out in cold or cool water, avoiding bleach, and drying on low heat or air drying are commonly recommended. Avoid ironing directly on the print.

Is screen printing the right method for your job?

Screen printing is typically most economical for repeat designs, bold colors and larger quantities, because the setup effort is spread across many shirts. For one-off shirts, photographic artwork or many colors, direct-to-garment (DTG), direct-to-film (DTF) or heat transfer vinyl may be more practical. If you are exploring the business side, see whether screen printing is a good side hustle, or read what screen printing T-shirts means for a short explainer.

Keep exploring

Guides from other topics

All topics →