Equipment and Supplies

Squeegee Durometer Guide: Choosing the Right Blade Hardness

Learn what squeegee durometer means in screen printing, how soft and hard blades change ink deposit and detail, and which blade hardness to start with for t-shirts.

On this page
  1. Short answer
  2. What durometer means
  3. Durometer chart
  4. Blade profile and sharpness
  5. Blade material, size and handle
  6. Angle and pressure
  7. Choosing by ink, mesh and job
  8. Care and replacement

Short answer

Durometer is a measure of how hard a squeegee blade is. In screen printing it is usually quoted on the Shore A scale. A softer blade (around the low-to-mid 60s) lets more ink through, a harder blade (around 80 and above) lets less through and holds finer detail, and a medium blade (roughly 70 to 75) is a common, versatile starting point for shirts. Treat these figures as typical ranges, not strict rules, and check what your supplier recommends for your press and ink.

What durometer means

Durometer measures how much a material resists indentation. A lower number is softer and more flexible; a higher number is harder and stiffer. For squeegees, hardness affects how much the blade flexes under pressure, which changes how much ink is pushed into and through the mesh.

Some manufacturers use color codes to indicate hardness, such as green for medium. These are not universal, so rely on the stated number rather than the color.

Durometer chart

Hardness (Shore A, approximate) Behavior Typical use
About 60–65 (soft) Flexes more, deposits more ink Heavy ink deposits, uneven or textured surfaces, some specialty inks
About 70–75 (medium) Balanced ink deposit and control General t-shirt printing, a common starting point for manual printing
About 80–85 and above (hard) Flexes less, deposits less ink, sharper edges Fine detail, halftones, fast automatic presses

One supplier of squeegee blades describes a medium blade of 75 Shore as appropriate for most uses, with softer 60–65 blades used to leave more ink on the item and harder 80–85 blades used on fast automatic machines for halftones, where less ink and more precision are wanted. Other suppliers cite 70 as their standard, so ask what your supplier’s “standard” means.

Dual and triple durometer blades

Some blades combine two or three hardness layers, such as a firm core with softer edges. This gives a firmer body for control while keeping the edge flexible. They are common on production presses, but a single-durometer blade is perfectly fine for hobby and small-shop work.

Blade profile and sharpness

The edge shape matters as much as the number:

  • Square edge: the standard choice for flat shirt printing, depositing a predictable layer of ink.
  • Rounded edge (D-cut): deposits more ink and is sometimes used for heavy, opaque prints.
  • Sharp edge: gives crisp control, and the ink deposit stays consistent.
  • Worn or rounded edge: deposits more ink and can change the final color. In shops that match brand colors, a blade that has lost its sharpness is known to shift results, which is a reason to resharpen or replace blades regularly. See screen printing ink for t-shirts for why color shifts happen.

Blade material, size and handle

Squeegee blades are usually made of rubber or polyurethane. Polyurethane is typically more durable and holds its edge longer, while rubber is generally cheaper but wears faster. Handles are made of wood or aluminum.

Choose a blade that is wider than your design, with room to spare on each side, and that fits comfortably inside the screen’s inside dimensions with space left for ink. Common blade widths range from about 4 inches for small projects to 18 inches or more for large screens. A very short blade in a big screen causes uneven pressure, and a blade almost as wide as the frame is hard to maneuver.

Angle and pressure

Hardness is only one of the variables you control. The squeegee angle changes the ink deposit too:

  • A lower angle (more tilted) tends to deposit more ink.
  • A more upright angle deposits less.
  • Many printers hold the blade at roughly 45 to 75 degrees and use firm, even pressure in one smooth stroke.

If you change several variables at once, you will not know which one caused the difference, so adjust one at a time. Hardness, mesh count and pressure all interact; see what mesh count to use for the mesh side.

Choosing by ink, mesh and job

  • Thick plastisol with a low mesh count (such as for white underbases): a medium blade is a common choice, with a softer blade if you need more ink.
  • Fine detail with a high mesh count: a harder blade, kept sharp, helps hold edges.
  • Water-based inks: often thinner, so a medium or harder blade can help prevent too much ink; follow ink-maker advice. See plastisol vs water-based ink.
  • Beginners: start with a single medium-hardness blade and a width that suits your screen, and adjust once you see how prints behave.

Care and replacement

  • Clean the blade after each session with the ink-appropriate cleaner, and dry it.
  • Store blades flat or hung so the edge does not deform.
  • Resharpen or replace blades when the edge rounds off, nicks appear, or ink starts to leak under the blade.
  • Avoid leaving blades sitting in solvents, which can degrade the material over time.

For the rest of a starter setup, see our equipment and supplies guide.

The complete guide to equipment and supplies

Screen Printing Equipment and Supplies: What You Need
Read the guide

Keep exploring

Guides from other topics

All topics →