The main types of t-shirt screen printing ink
Most shirt printing uses one of three ink families, plus a range of specialty additives and finishes. The right choice depends on the garment’s fiber and color, the feel you want, and the equipment you have for curing.
Plastisol
Plastisol is made of PVC particles suspended in a liquid plasticizer. It stays wet in the screen until it is heated, so it does not dry in the mesh while you work, which makes it forgiving for beginners and for long runs. It prints opaque on dark garments and is the most common ink for shirts. The ink film sits on top of the fabric and can feel thicker or “rubbery,” and plastisol needs solvent-based cleanup. Most plastisols need to reach a cure temperature in the range of roughly 300–330°F (150–165°C) through the full ink film, but always check the manufacturer’s data sheet. For a closer comparison, see plastisol vs water-based ink.
Water-based ink
Water-based inks use water as the main carrier and tend to soak into the fibers, giving a softer, more breathable feel. They suit light garments and natural fibers like cotton well. Downsides include:
- they can dry in the screen and clog the mesh during pauses
- standard formulas are often semi-transparent and less vivid on dark shirts
- the stencil takes more punishment, so a water-resistant emulsion is usually needed
- they need enough heat and time to evaporate the water and cure properly
Craft fabric inks from art-supply brands are generally water-based acrylics.
Discharge ink
Discharge inks remove dye from the fabric where they are printed rather than covering it. They give a very soft print on suitable dyed cotton and are popular for a vintage look. They do not work on every garment dye, and they require extra care with mixing, ventilation and testing, so they are best treated as a second step after you are comfortable with the basics.
Specialty inks and additives
Puff, glitter, metallic, high-density, glow-in-the-dark and soft-hand additives are available, mostly for plastisol. Thick effect inks usually need a lower mesh count (more open mesh); our mesh count guide covers how that works.
Matching ink to shirt color and fabric
- Light cotton: almost any ink type works; water-based inks look good.
- Dark cotton: plastisol with a white underbase is the common approach. Print white first, flash it until it is dry to the touch, then print color over it. Discharge is another route on suitable fabrics.
- Polyester and blends: dyes in polyester can migrate into the ink during curing, making white or light inks turn pink or gray. Low-bleed, low-cure inks are made for this problem. Always test a garment before running a batch.
- Fabric choice itself matters too; see what type of material is used for t-shirts.
Pantone and color matching
Pantone is a standardized color system, widely used by brands to specify exact colors with numbered swatches, such as a particular red. A client may ask you to match a Pantone color on a shirt.
In practice, matching works like this:
- Start from the supplier’s mixing system. Ink makers publish formulas to mix base inks into Pantone colors, and many shops use mixing software or a mixing system from the ink supplier. Home printers can ask a supplier for a pre-mixed color.
- Print a test on the actual garment. The color that comes out depends on the shirt color, the fabric blend, the underbase, and the ink brand.
- Compare to the swatch in good light. Check it in daylight and indoors; a color that matches in one light may drift in another.
- Adjust and record. If you modify the formula, write it down so you can repeat it on the next order.
Do not expect a perfect match on every shirt. Printed ink on fabric is not the same as ink on coated paper, and the Pantone book is printed on paper.
Why colors print differently than the swatch
Several shop variables change the final shade:
- Mesh count and stencil thickness change how much ink is deposited.
- Squeegee sharpness and pressure: a worn, rounded blade can push through more ink. Our squeegee durometer guide explains the blade side.
- Wet-on-wet printing, where one color is printed over another that has not been flashed, can pick up ink on the screen and lighten the result.
- Underbase and fabric color change how light reflects.
For a single hobby print, “close enough” may be fine. For brand work, plan on test prints and written formulas.
Curing basics
Whatever ink you use, curing is what makes it permanent. Plastisol needs heat; water-based inks need the water driven off plus heat setting; discharge and specialty inks have their own instructions. Under-cured prints can crack or wash out, so many printers stretch-test a cooled print, and use an infrared thermometer or probe to check the ink temperature, not just the dryer setting.
Choosing ink for a beginner
If you are just starting, plastisol is generally the most forgiving because it does not dry in the screen, though it needs a heat source capable of reaching cure temperature. If you only have a craft setup and want to cure by iron or heat gun, a water-based fabric ink made for that purpose may be more practical. Either way, pair it with a sensible mesh and a good emulsion, and see the complete equipment and supplies guide for the other pieces. For a rubbery-feel print, read about rubber ink for t-shirt printing.