Printing Process

How to Screen Print White Ink on Black T-Shirts

How to screen print white ink on black T-shirts: underbases, mesh choice, flashing, ink options and common problems like dye bleed and low opacity.

On this page
  1. Why white on black is harder than it looks
  2. Choose an ink: plastisol, water-based or discharge
  3. Pick the right mesh and stencil
  4. Print it: one hit, double hit, or print-flash-print
  5. Flash and cure properly
  6. Common problems on black shirts
  7. Downsides of each ink option
  8. When to consider other methods

Why white on black is harder than it looks

On a white shirt, ink only has to add color. On a black shirt, the ink has to cover the dark fabric. Thin or translucent ink will look gray, dull or blotchy, because the black underneath shows through. Fibers can also stand up through wet ink, and some dyes can migrate into a white print when it is heated.

The good news is that a single-color white design on a black shirt is one of the more common jobs in screen printing, and a few choices go a long way: the ink, the mesh, how many passes you print, and curing.

Choose an ink: plastisol, water-based or discharge

Plastisol. The most common choice for white on dark garments. It is thick and opaque, sits on top of the fabric and does not dry in the screen, which makes it forgiving for beginners. The downside is a heavier, more plastic feel on the shirt, especially on big designs. Plastisol is commonly cured at about 320°F (160°C); follow your ink maker’s data sheet. Look for ink labeled as high-opacity or made for dark garments.

Water-based ink. It soaks into the fibers and gives a soft feel, but standard water-based white can look weaker on black unless the ink is formulated for opacity. It dries faster in the screen, so you need to keep the screen flooded or add a retarder, and it needs enough heat and time to dry and cure, since water must evaporate first. Many printers consider it better for light garments and some specialty uses.

Discharge ink. A discharge system uses an activator to remove the dye from suitable fabric, typically 100% cotton, and replaces it with pigment. The result can be very soft. It depends strongly on the fabric and dye, requires good ventilation, and needs careful handling, so follow the manufacturer’s safety instructions. Test on the actual blank, since results vary.

If you are not sure, begin with a high-opacity plastisol white.

Pick the right mesh and stencil

A lower mesh count lets more ink through, which helps opacity. For white on black, many printers use a mesh somewhere around the 110 to 160 range, depending on the ink and design. One industry demonstration for discharge on black used a 156 mesh to get good ink saturation, and higher counts for halftone or fine detail. Test a couple of mesh counts if you can.

A well-coated stencil with a bit of thickness also helps, because it lays down a more consistent ink deposit. See how to coat a screen with emulsion evenly.

  1. Single hit. One stroke, one pass. Works with some high-opacity inks on some garments, but often looks a bit thin on black.
  2. Double hit (wet-on-wet). Print, then lower the screen and print again over the wet ink without lifting the shirt. This can build opacity, but it can also cause blurring if the registration shifts.
  3. Print-flash-print. Print a first layer, flash it so it gels and no longer feels wet, then print a second layer. Flashing helps the second layer stay crisp and bright. This is the most common approach for an opaque white on black, and it is how white underbases for multi-color designs are made.

Other pointers:

  • Use the sharp edge of the squeegee and a consistent angle.
  • For plastisol, many printers use lighter pressure so the ink sits on the shirt, while water-based and discharge generally need firmer pressure to work the ink into the fibers. Avoid bending the blade.
  • Use a lint roller on the shirt first, since lint stands out on dark fabric.
  • Keep the off-contact steady so the screen releases cleanly. If you suspect ghosting, see screen printing defects and how to fix them.

Flash and cure properly

When you flash, you only want to gel the ink enough to stop it from smearing or lifting when you print over it. Overflashing makes the next layer sit poorly and may cause adhesion problems. After the last layer, cure the whole print. For plastisol that generally means getting the ink film temperature to about 320°F, checked with an infrared thermometer or probe. Water-based and discharge inks need a long enough dwell for moisture to leave and the ink to cure. One manufacturer demonstration suggested aiming for around 320°F for those inks to reduce wash-out. Follow your ink’s instructions.

Before running a batch, stretch and wash-test a sample to check for cracking or fading.

Common problems on black shirts

  • White looks gray or thin. Use a high-opacity ink, a lower mesh count, a double hit or print-flash-print, and check your stencil’s thickness.
  • Fuzzy fibers in the print. Lint-roll the shirt, and consider a quick pre-flash or pre-press for fuzzy fabrics.
  • Dye bleed (pink or yellow tint in the white). Common on polyester or poly blends. Use a low-bleed ink, lower cure temperature if allowed, and test on the exact garment.
  • Cracking. Often an under-cure, though a thick plastisol deposit can also crack when stretched.
  • Blurry edges on double hits. Registration or off-contact has shifted. Try print-flash-print instead.

Downsides of each ink option

Ink Main advantages Main downsides
Plastisol Opaque, forgiving, does not dry in screen Heavier feel, contains PVC, needs sufficient heat
Water-based Soft hand, breathable Dries in screen, needs care for opacity on dark shirts, requires full drying and curing
Discharge Very soft feel on suitable cotton Fabric-dependent, needs ventilation and careful handling, inconsistent on some dyes

When to consider other methods

For tiny runs, photographic artwork or a lot of colors on black, direct-to-garment or direct-to-film printing may be easier. For bold one- or two-color designs in a repeatable run, screen printing is hard to beat. If you plan to add colors over a white underbase, see four-color process screen printing, and for the overall workflow, see the step-by-step screen printing guide.

The complete guide to printing process

How to Screen Print T-Shirts: A Step-by-Step Guide
Read the guide

Keep exploring

Guides from other topics

All topics →