Printing Process

How to Expose a Screen Without an Exposure Unit: Sunlight, Lamps and Clamp Lights

Expose a screen without an exposure unit using sunlight, halogen work lamps or clamp lights. Learn setup, safety and how to test your exposure time.

On this page
  1. What an exposure unit actually does
  2. What you need for a DIY setup
  3. Option 1: Sunlight
  4. Option 2: Halogen work lights
  5. Option 3: Clamp lamps with UV or blacklight bulbs
  6. Build a simple contact setup
  7. Find your exposure time with a test
  8. Safety
  9. When a DIY setup stops being enough

What an exposure unit actually does

An exposure unit holds your film flat against a coated screen and shines an even, UV-rich light across it for a timed period. It does three jobs: it gives a consistent amount of light, it keeps the film in tight contact with the screen, and it blocks other light. A home setup needs to do the same three things. If you can get all three right, you can make good stencils without buying a unit.

The rest of the process, from artwork to printing, is in our screen printing guide.

What you need for a DIY setup

  • A coated, fully dry screen, made as described in how to coat a screen with emulsion evenly.
  • A dense film positive. See making film positives.
  • A light source (see the options below).
  • A dark, flat backing to put under the screen, such as black foam board, black fabric or black felt, to stop light from bouncing back through the emulsion.
  • A sheet of clean glass or clear acrylic to press the film flat, sized to cover the design. Some printers use a weight or a board with foam, but glass is the most common.
  • Something opaque to cover the screen while you set up, such as a black sheet or cardboard box.
  • A timer.
  • Safety glasses that block UV, particularly with halogen and UV lamps.

A dim, no-UV room helps while setting up. Do not unwrap or move coated screens in daylight.

Option 1: Sunlight

Sunlight contains plenty of UV and can expose screens, but it varies with time of day, cloud, season and location, so results are less repeatable.

  • Prepare everything indoors, in the dark. Place the dark backing, then the screen with the flat shirt side facing up, then the film with the inked side against the screen, then the glass on top.
  • Carry the sandwich outside under a dark cover, such as a black sheet or box, and uncover it only when you are ready to start the timer.
  • Choose bright, clear conditions and keep the screen flat and still. Shadows moving across the screen can ruin an exposure.
  • Cover the screen again as soon as the time is up.

Because the light is so variable, run a test for each session instead of relying on a past number. It is workable for occasional prints, but frustrating for regular production.

Option 2: Halogen work lights

A 500-watt halogen work light is a classic budget choice. It produces some UV, along with a lot of heat, so exposure times are usually longer than with a proper unit. One supplier suggests using about 1-minute test intervals for 500W halogen setups, which gives an idea of the time scale compared with faster units.

Tips:

  • Mount the light on a stand or frame pointing straight down at the screen, and keep the distance the same every time. Use a tape measure.
  • Make sure the light covers the whole design evenly. A single bulb tends to be brighter in the center, so a larger distance can help but increases exposure time.
  • Heat is a real concern. Excess heat can damage film, glass, emulsion and nearby objects. Never leave a halogen lamp unattended, keep it away from flammable items, and be careful with mounting. Fire and burn hazards are real.
  • Let bulbs warm up to stable output before starting a timed exposure, if the manufacturer suggests it.

Option 3: Clamp lamps with UV or blacklight bulbs

Many printers use ordinary clamp lights with blacklight or UV bulbs, or LED UV lamps. Output differs widely, and not all “blacklight” bulbs produce enough UV in the right range to harden emulsion in a reasonable time, so check what the bulb and the emulsion maker specify.

  • Use several lamps or a bank of tubes to cover the screen evenly, rather than a single lamp.
  • Place them an equal distance from the screen and keep that distance fixed.
  • Expect longer times than a commercial unit and test carefully.
  • LED UV options run cooler than halogen but can still be bright, so wear eye protection and do not look at the lamps.

Build a simple contact setup

  1. Lay the dark backing on a flat table.
  2. Place the coated screen on it with the shirt side up, so the flat side of the mesh is facing the light.
  3. Put the film on the screen with the inked side down against the emulsion. In this layout the artwork should look mirrored when you look down through the film, and read correctly when viewed from the squeegee side. If you are unsure, do a quick test with text.
  4. Lay the glass on top. Press down gently so that the film touches the screen over its whole area. If the film lifts at the edges or the glass does not sit flat, light can undercut the design and ruin edges.
  5. Check the glass for dust, since specks can cast shadows on the emulsion.
  6. Position the light, start the timer, and cover the screen immediately when the time ends.

Find your exposure time with a test

Exposure time is the hardest part of a DIY setup, because your light, distance and emulsion are unique. Use an exposure calculator or a step test rather than guessing. Our guide to how long to expose screen printing emulsion explains how to run and read the test.

Once you find a time that works, keep every variable the same: distance, bulb, backing, glass and coating. Write it all down.

Safety

  • Wear eye protection and avoid looking at UV or halogen lamps.
  • Keep the area ventilated and clear of flammable materials, and never leave heat lamps unattended.
  • Take care with glass edges, hot bulbs and electrical cables, and keep cords out of water when you wash out the screen.
  • Keep coated screens covered until you are ready to expose.

When a DIY setup stops being enough

A homemade setup is a fine way to start, and many people make good stencils with it. If you find that your exposures are inconsistent, you are spending a lot of time on testing, or you are producing more screens, a purpose-built exposure unit with a vacuum or a good contact system can make results more repeatable. If your stencils break down or look uneven, check screen printing defects and how to fix them for other possible causes.

The complete guide to printing process

How to Screen Print T-Shirts: A Step-by-Step Guide
Read the guide

Keep exploring

Guides from other topics

All topics →