Printing Process

Four-Color Process Screen Printing Explained

Four-color process screen printing explained: how CMYK halftones, mesh, moiré, underbases and registration work, and when it makes sense to use it.

On this page
  1. What four-color process means
  2. Four-color process vs spot color vs simulated process
  3. How the process works
  4. Print order and ink choices
  5. Printing on dark shirts
  6. Doing it on a manual press
  7. Common problems: moiré, dot gain and misregistration
  8. Is it worth it? Alternatives like DTG and DTF

What four-color process means

Four-color process printing recreates full-color images using just four inks: cyan, magenta, yellow and black, usually shortened to CMYK. Instead of printing a solid area of each color, the image is broken into patterns of tiny dots called halftones. When the dots overlap and sit side by side, the eye blends them into a wide range of colors and gradients.

In screen printing, each ink color has its own screen, so a basic four-color process job uses four screens, plus a fifth for a white underbase if the shirt is dark. It is the same press and the same basic steps as simpler printing, covered in our guide to screen printing T-shirts, but the tolerances are much tighter.

Four-color process vs spot color vs simulated process

  • Spot color: each color in the design is a single ink, usually matched to a specific color. Best for logos and bold graphics.
  • Four-color process (CMYK): a limited set of transparent inks printed as halftone dots to build photographic color. The ink is typically translucent, so it works best on white or light shirts, or over a white underbase.
  • Simulated process: a different approach where the image is separated into a number of opaque spot colors, often with a white underbase, and halftones blend them. It is commonly used for dark garments and can give more punch than straight CMYK, but it takes more screens and more skill.

The more colors and halftones a design needs, the more screens, setup and registration work it requires.

How the process works

Separations

The artwork is split into four channels, one for each ink. Software exports each channel as a black-and-white halftone film, with the density of the dots representing how much of that ink goes there. These films are then used to expose four screens as usual. For tips on output quality, see how to make film positives; halftones need especially dense, sharp film.

Mesh and halftone frequency

Fine dots need a fine mesh. Sources commonly cite high mesh counts, around 305, with halftone frequencies in the range of roughly 55 to 65 lines per inch for textile work. These are starting points, not rules. The right combination depends on your ink, your stencil quality and your press, so test before committing to a job.

Dot shape and angles

If the four screens use halftone dots lined up the same way, they can interfere with each other and with the mesh itself, producing a wavy, repeating pattern called moiré. To avoid it, each channel is output at a different angle, and many printers use elliptical dots. Separation software usually offers presets, but the best settings depend on your mesh and printer, so treat any preset as a starting point.

Process inks are typically printed wet-on-wet or with a quick flash between colors, in an order chosen to keep colors clean. A common starting point is lightest to darkest, yellow, magenta, cyan and then black, though shops vary. Use inks made for process printing, and make sure they cure compatibly with the rest of your setup.

Because inks are translucent, the order, ink thickness and stencil quality all influence the final color. Expect to do test prints and adjust.

Printing on dark shirts

On a dark garment, CMYK ink alone will look dull, since the shirt color shows through. The usual fix is to print a white underbase first, flash it so it gels, and then print the color layers on top. That adds a screen and a flashing step. Our article on screen printing white on black T-shirts goes through the underbase approach.

Doing it on a manual press

It is possible on a manual press with micro-registration, but it is demanding. Every screen must line up with the previous one to a very small tolerance, and your stroke pressure, ink deposit and off-contact need to stay consistent from print to print. Automatic presses are better at this because they repeat the same stroke the same way. If you try it by hand:

  • Use stable, well-tensioned screens and keep the same off-contact for each color.
  • Add registration marks to the films and follow our guide to multi-color registration.
  • Start with a simple image with large smooth tones and few fine details.
  • Test on scrap shirts until the image looks right.

Common problems: moiré, dot gain and misregistration

  • Moiré: a repeating wavy pattern. Try changing screen angles, halftone frequency or mesh count.
  • Dot gain: dots print larger than designed, making the image dark and muddy. This can come from too much ink, too much pressure or an incorrect off-contact distance. Adjust the technique and compensate in the separations.
  • Misregistration: colors drift apart, producing fuzzy edges and color fringes. Re-check registration marks and tension.
  • Weak stencils: fine dots can wash away if exposure is wrong. See the defects guide for more, in screen printing defects and how to fix them.

Is it worth it? Alternatives like DTG and DTF

Four-color process is one of the harder screen printing techniques, and it can be time-consuming to set up. It makes the most sense for larger runs of a full-color design, where the setup cost is shared across many shirts. For small quantities of photographic art, direct-to-garment (DTG) or direct-to-film (DTF) printing is often easier, since there are no screens or registration to deal with. Which method looks and feels best depends on the fabric and design, so ask for samples if you are deciding for a job.

If you are new to screen printing, it is usually wise to master one- and two-color prints first.

The complete guide to printing process

How to Screen Print T-Shirts: A Step-by-Step Guide
Read the guide

Keep exploring

Guides from other topics

All topics →