Equipment and Supplies

What Mesh Count to Use for Screen Printing T-Shirts

Choose the right screen printing mesh count for t-shirts. See which counts suit white underbases, general plastisol, fine detail, water-based ink and special effects.

On this page
  1. Short answer
  2. What mesh count means
  3. Mesh count chart for t-shirt printing
  4. How ink type changes the choice
  5. Mesh color, material and tension
  6. Choosing one mesh when you can only buy one
  7. Troubleshooting mesh-related problems

Short answer

For most t-shirt printing with plastisol, a mesh in the 110 to 160 range is a common starting point for solid colors and white underbases, and 160 to 230 is common for general artwork with some detail. Fine detail and halftones typically call for 200 to 305. Thick special-effect inks such as puff or glitter usually need a lower count, roughly 60 to 110. If you can only buy one screen to start, something around 110 to 160 is a reasonable all-rounder. Treat these as starting ranges and confirm with your ink’s data sheet and a test print.

What mesh count means

Mesh count is the number of threads per inch of the screen. A higher number means more threads, smaller openings, and less ink passing through. A lower number means larger openings and more ink.

Some suppliers list mesh by threads per centimeter instead. To convert, multiply by 2.54: a 43T mesh is roughly 110 threads per inch, and a 77T mesh is roughly 195. Check which unit a listing uses before you compare.

Mesh count is not the only variable. Thread diameter, mesh color, stencil thickness and tension all affect how much ink ends up on the shirt.

Mesh count chart for t-shirt printing

Use Typical mesh count (threads per inch) Why
Special-effect inks (puff, glitter, shimmer) about 60–110 Thick inks need big openings
White underbase on dark shirts about 110–160 Heavy deposit for opacity
Bold, solid plastisol colors about 110–200 Good coverage with decent edges
General artwork with some detail about 160–230 Balance of detail and ink
Fine lines, small text, halftones about 200–305 Smaller openings hold detail
Water-based ink often higher than for plastisol Thinner ink; check supplier advice

Different suppliers publish slightly different recommendations, so use these as ranges, not rules. For example, one aluminum frame supplier suggests 110 for heavy deposits such as white on dark shirts, 156 for general printing, and 230 to 305 for high-detail halftones.

How ink type changes the choice

  • Plastisol is thick and stays wet in the screen, so it needs enough open mesh to pass through. Lower counts suit opaque and underbase prints; mid and higher counts suit detail.
  • Water-based ink is thinner and soaks into the fabric. A finer mesh often works because it deposits a thinner layer, though results depend on the ink. Remember that water-based inks can dry in the screen and need a water-resistant emulsion; see plastisol vs water-based ink.
  • Discharge and specialty inks vary, so follow the product instructions.

A finer mesh also lays down a thinner ink film, which can give a softer feel on the shirt, while a coarse mesh gives a more opaque, raised print.

Mesh color, material and tension

  • Material: polyester is the standard for shirt printing; it is durable, affordable and holds tension well. Nylon stretches more, and stainless steel is used for industrial work.
  • Color: white mesh is fine for most work. Yellow or dyed mesh reduces light scatter during exposure and can help with fine detail.
  • Tension: a screen that is too loose will not snap off the shirt, leading to blurry, smeared prints. Pre-stretched aluminum frames usually have consistent tension; see aluminum vs wood frames and how to stretch your own screens.
  • Emulsion thickness: a thicker stencil can reduce ink deposit and sharpen edges, while a thin one allows more ink through. See choosing a screen printing emulsion.

Choosing one mesh when you can only buy one

If you are buying your first screen:

  • For bold one- to three-color designs on cotton shirts, pick a mid-range count such as 110 to 160.
  • If you plan to print mostly detailed artwork, move up toward 200 or higher, accepting that thick inks may not pass through easily.
  • If you want to print on dark shirts with a white underbase, choose a count at the lower end of the mid-range.

Over time, most printers keep several mesh counts on hand rather than looking for one that does everything.

  • Print looks thin, grainy or washed out: the mesh may be too fine for the ink, or the squeegee pressure too light. Try a lower count or a second pass.
  • Ink floods through, blurry edges, or too much ink on the shirt: the mesh may be too coarse, there may be too much ink, or pressure may be too heavy. Use a higher count or lighter pressure.
  • Detail fills in or disappears: the mesh may be too coarse for the artwork or the stencil under-exposed.
  • Ghosting or smearing: check tension and the off-contact gap rather than mesh alone.

Blade choice also affects how much ink is pushed through; our squeegee durometer guide covers that side. For everything else you need to set up, see the equipment and supplies guide.

The complete guide to equipment and supplies

Screen Printing Equipment and Supplies: What You Need
Read the guide

Keep exploring

Guides from other topics

All topics →