Equipment and Supplies

Can I screen print without a press?

Yes, you can screen print without a press using hand-held screens, clamps and simple stencils. Learn the methods, steps, limits and when a press is worth having.

On this page
  1. Short answer
  2. Ways to print without a press
  3. Step-by-step: printing freehand
  4. What you give up without a press
  5. Curing at home
  6. When to build or buy a press

Short answer

Yes. A press is a convenience, not a requirement. For single prints, small batches and one-color designs, many people print by holding the screen in place by hand or by clamping it to a table. Where a press really helps is multi-color work and repeat runs, because it keeps the screen and the shirt in the same position every time.

Ways to print without a press

  • Hold the screen by hand. Lay the garment flat, place the screen on top, hold it steady with one hand and pull the squeegee with the other. Having a second person hold the screen makes it much easier.
  • Clamp the screen to a table or board. Cheap clamps, or hinge clamps screwed to a board, act as a simple hinge so the screen lifts and lowers in the same place. This is the step between “no press” and a homemade one; see how to build your own screen printing press.
  • Use a paper or tape stencil. Cut a stencil from paper, vinyl or tape and place it under the screen. Because there is no emulsion step, it is a very low-cost way to try printing.
  • Use screen filler and drawing fluid. Paint the design onto the mesh with water-soluble drawing fluid, coat the screen with filler, let it dry, then wash out the drawing fluid to leave the design open.
  • Use a glue or similar blocking method. Some people block the non-design areas with a water-soluble glue. Results vary, so test first.

You can also make a screen without a darkroom, which is covered in how to make and stretch your own screens.

Step-by-step: printing freehand

  1. Prepare the stencil using one of the methods above, or a photo-emulsion stencil if you have one.
  2. Prepare the garment. Lay the shirt flat and slip a piece of cardboard inside so ink does not soak through to the back. A light spray of adhesive on the board can help keep the fabric from sliding.
  3. Position the screen. Place it over the shirt, centered on your design, and hold it firmly or clamp it.
  4. Add ink. Put a line of ink along the top of the screen above the design.
  5. Flood. Holding the squeegee at roughly a 45-degree angle, gently pull the ink across the design to fill the mesh.
  6. Print. Pull the squeegee back across with firm, even pressure so the ink goes through.
  7. Lift straight up. Remove the screen without dragging it, to avoid smudging.
  8. Dry and cure the ink according to the ink maker’s instructions.

Practice on scrap fabric first. If you are using water-based ink, wash the screen promptly, because the ink can dry in the mesh.

What you give up without a press

  • Registration. Lining up a second or third color by hand is difficult. Without hinges or registration marks, colors will not align reliably.
  • Consistency. A held screen can shift, causing ghosting or double images.
  • Speed. Repositioning the screen for each shirt takes longer.
  • Off-contact. Without a set gap, the mesh can stick to the shirt and smear, which affects crisp edges.
  • Fine detail. Details such as small text and halftones are harder to hold without stable positioning.

Curing at home

How you cure depends on the ink. Many water-based craft fabric inks are designed to be heat-set with an iron or heat press following the label directions. Plastisol needs to reach its full cure temperature, which a household iron may not reliably deliver, so a heat press, heat gun with a temperature probe, or a dryer is usually used. Never iron directly on a plastisol print unless the manufacturer says it is safe. See plastisol vs water-based ink for the differences.

When to build or buy a press

Consider a press if you:

  • print multi-color designs
  • print the same design repeatedly
  • want faster, more consistent results
  • are starting to sell shirts

A DIY hinge-clamp build is a cheap first step, and a purchased manual press is the next one. For a full list of what a home setup needs, read our equipment and supplies guide, or look at home screen printing kits if you want something ready to go.

The complete guide to equipment and supplies

Screen Printing Equipment and Supplies: What You Need
Read the guide

Keep exploring

Guides from other topics

All topics →