Printing Process

How to Register Multi-Color Screen Prints So Colors Line Up

How to register multi-color screen prints so colors line up: marks, film placement, press setup, off-contact, trapping and fixing common misalignment.

On this page
  1. What registration is and why it slips
  2. Build registration into the artwork
  3. Place the film consistently when exposing
  4. Set up the press
  5. Line up the screens
  6. Print order and flashing
  7. Trapping and overlap
  8. Fix common registration problems
  9. Keep it repeatable

What registration is and why it slips

Registration is the alignment of each color layer to the others, so that every part of a multi-color design lands where it belongs. When registration is off, you see gaps between colors, overlapping edges, white lines or fuzzy outlines.

Registration can drift for many reasons: marks placed inconsistently on the film, a screen that is not square in the frame, low screen tension, loose clamps, a shifting garment, changes in off-contact between screens, or ink that stretches the mesh differently as it dries. Small errors can add up, and on a long run they can multiply.

Because every color needs its own screen, this step is the heart of multi-color work. The overall process is covered in our guide to screen printing T-shirts.

Build registration into the artwork

  • Add registration marks such as crosshairs or small circles to each color separation, in the same position on each film. Placing them in the corners, or at the top and bottom of the design, outside the print area, is common.
  • Name and order the layers by print order and color. One designer suggests labeling layers like “pattern_layer1_pink” so there is no confusion later.
  • Lock the marks in your software so they cannot move between separations.
  • Keep the design centered on a consistent anchor point across all layers.
  • Print film at the same size and check that no scaling has crept in.

For good film, see making film positives. Registration marks must be sharp and dense, since a fuzzy mark makes alignment harder.

Place the film consistently when exposing

If you place each film in a different position on its screen, you may exceed the adjustment range of your press when trying to align the colors. Pick a standard way to position film, for example, centered side to side with the top of the design a fixed distance from the top of the frame, and use the same method on every screen. Tape the film in place before exposing so it does not shift. An exposure supplier notes that designs should sit on screens in a very similar way, so the press adjustments are enough to line things up.

A lined-up stencil also depends on good exposure and washout, as covered in how long to expose screen printing emulsion.

Set up the press

  • Use tight, even screens of the same size, with good tension. Printers who track screen tension and retire slack screens report fewer registration issues.
  • Check the frames for warping or damage.
  • Tighten clamps so the screen does not shift during printing.
  • Use the same off-contact for every screen. A different gap can stretch the image differently.
  • Fix the garment position with a platen guide, pallet adhesive and a consistent loading routine, so each shirt sits in the same place.
  • Mark the platen with tape or a stop so you can load quickly and accurately.

Line up the screens

On a manual press, a common method is:

  1. Put a clear sheet of film, acetate or paper on the platen, secured with tape.
  2. Print the first color on the sheet, or lay a registration print down, so you have a reference of where color one lands.
  3. Lower the second screen. Without ink, look through or at the screen and compare its marks to the reference print.
  4. Adjust the screen using micro-registration knobs, if you have them, or by loosening and shifting the clamps, until the marks line up exactly.
  5. Lock the screen in place, then check again.
  6. Repeat for each additional screen, always against the same reference.

Some printers use clear acetate with the first-color print, others tape a printed sheet to the platen. Whichever you use, keep the reference stable until all screens are set.

If your press has only one station, you will print color one on all garments, let or flash the ink so it does not smear, and then change the screen, re-register it and print color two. Take care that you do not move the platen guides or garment position between colors.

Printers often print from the lightest color to the darkest, with an outline or black detail last, although the right order depends on your design and the ink. Name colors in print order in your artwork, and check the order on a test shirt. If you print wet-on-wet, keep your strokes consistent. If a color goes over another, a quick flash between layers can help the ink stay put, but test the process. An overflashed layer may not bond well with the next layer.

Trapping and overlap

Even good registration can be a hair off. To hide small misalignments, designers add trapping, a tiny overlap where one color meets another. The lighter color can slightly extend under the darker color, or the colors can overlap by a thin amount. The right amount depends on your press, mesh and design, so start small and test. Without trapping, a small shift shows up as a white gap.

Fix common registration problems

Problem Likely cause What to try
Whole color shifted Screen not positioned correctly Realign with reference marks
Drift over the run Clamps loosening, garments shifting Retighten, check loading routine
One side off, other fine Screen skewed or frame warped Square the screen, check the frame
Colors fuzzy Off-contact too high, too much pressure Adjust off-contact, reduce pressure
Image stretches Low tension, high pressure Re-tension or replace the screen
Marks do not match Film printed or placed differently Reprint film, use same placement method
White gaps No trapping Add overlap in artwork

Our guide to screen printing defects covers other problems you might see in a multi-color run.

Keep it repeatable

  • Create a standard method for film placement, screen mounting and garment loading, and follow it each time.
  • Label screens by job and color, and store them so they are not damaged.
  • Record press settings for a job so you can recreate them for reprints.
  • Make a test print before every run and check each color.

For complex designs such as halftones and process color, registration tolerances are even tighter, as explained in four-color process screen printing. For a lower-tech approach to a few colors, you can also use vinyl stencils, as described in how to screen print shirts with Silhouette vinyl stencils.

The complete guide to printing process

How to Screen Print T-Shirts: A Step-by-Step Guide
Read the guide

Keep exploring

Guides from other topics

All topics →