What reclaiming means
Reclaiming a screen means removing the ink and the old stencil from the mesh so you can coat it again and burn a new design. A well-reclaimed screen can be reused many times, which is one of the things that makes screen printing economical. It is the last step of our step-by-step screen printing guide and the first step before coating a screen with emulsion.
Supplies
- Ink cleaner or press wash suited to your ink type, and rags or paper towels.
- A plastic scraper or squeegee for removing bulk ink.
- Emulsion remover, sometimes called stencil remover.
- Haze remover or degreaser, optional but helpful for ghost images.
- A soft nylon brush or scrub pad that is gentle on mesh. Avoid metal brushes or harsh abrasives.
- A pressure washer, hose or sink sprayer and somewhere suitable to wash out.
- Gloves, eye protection and an apron. Emulsion removers and cleaners can irritate skin and eyes, so follow the label.
- Good ventilation, since cleaners may give off fumes.
Step 1: Remove tape and ink
- Scrape off as much leftover ink as you can with a spatula, card or scraper, and put it back in the container if you plan to reuse it.
- Peel off all tape before the screen gets wet. Tape that has been soaked is harder to remove, and residue can stay in the mesh.
- Apply ink cleaner or press wash to both sides of the mesh and wipe it clean with a rag. Repeat until the cloth comes away clean.
- Rinse off the cleaner if the product says to.
Ink left in the mesh will cause a haze or ghost image and may keep emulsion remover from reaching the stencil.
Step 2: Strip the emulsion
- Wet the screen with water.
- Apply emulsion remover generously to both sides of the mesh, using a brush or a spray bottle depending on the product.
- Gently scrub with a soft nylon brush.
- Let the remover sit for the time the label recommends, commonly in the range of tens of seconds to a couple of minutes.
- Do not let the remover dry on the screen. Dried remover and dissolved emulsion can leave a film, and some emulsion can be harder to remove afterward.
Work on one screen at a time and keep the surface wet.
Step 3: Rinse or pressure wash
Rinse from the shirt side or squeegee side, whichever lets the dissolved emulsion flow out of the mesh. With a pressure washer, keep the nozzle at a sensible distance from the mesh and avoid concentrating the spray in one spot, since high pressure can damage or tear the mesh. Many printers hold the wand several inches away and work from the bottom up. A garden hose or sink sprayer with a good nozzle also works for light stencils, though it may take longer.
Rinse until the water runs clear and the stencil is gone.
Step 4: Deal with ghost images and haze
A ghost image is a faint shadow of an old design left in the mesh, often from ink or emulsion that stayed in the knuckles of the mesh threads. A haze is a general cloudy residue.
- Apply a haze remover or an all-in-one degreaser and dehazer to the affected area.
- Scrub lightly and let it sit for the time the label recommends, often a few minutes at most.
- Rinse thoroughly with water.
Some ghosting may never fully disappear, especially with older or dyed mesh, but it is often cosmetic and does not stop the screen from working. If the ghost is in an area where you will print a fine detail, test it with a dummy exposure first. Persistent heavy ghosting after a thorough clean can be a sign that the screen has reached the end of its useful life.
Step 5: Degrease, dry and inspect
- Clean the mesh with a degreaser, as you would before coating.
- Rinse well, since leftover chemicals can interfere with emulsion adhesion.
- Wipe the frame with a clean towel, taking care not to touch the wet mesh.
- Dry the screen in a rack or cabinet with good airflow.
- Hold it up to a light to look for holes, thin spots, tears, or leftover emulsion.
- If you spot damage, patch or retire the screen. A screen that has lost tension, which you can measure with a tension meter, can cause registration and print quality problems.
Reclaiming without a pressure washer
You can reclaim screens at home without a pressure washer:
- Use a utility sink or a hose with a spray nozzle.
- Use a bit more remover and a bit more patience, scrubbing gently with a soft brush on both sides.
- Rinse from several angles until all emulsion is gone.
- Do not blast concentrated high pressure from very close, even with household equipment, since it can damage mesh.
Check local rules about what can go down your drain, since emulsion, remover and ink residue may have restrictions in some areas. Capture and dispose of waste properly if required.
Troubleshooting stubborn stencils
- Stencil will not dissolve. Overexposed or very thick stencils can be tough. Apply more remover, let it dwell without drying, and scrub gently. Some hard stencils may need a stronger remover suited to the emulsion.
- Dried emulsion remover. Rewet the screen and apply fresh remover.
- Leftover ink in the mesh. Use more press wash or ink degrader first, and clean both sides.
- Tape residue. Use an appropriate adhesive remover or ink cleaner, then degrease again.
- Dull or sticky spots. Often leftover chemical or emulsion. Rinse again with plenty of water.
For problems with stencils that reappear on screens you have just prepared, check screen printing defects and how to fix them.
Safety and waste
Wear gloves and eye protection, ventilate the area, keep chemicals in labeled containers, and follow the safety sheets from the manufacturers. Do not mix different cleaners unless the labels say it is safe. Dispose of waste according to your local rules. A routine of cleaning screens promptly after printing makes reclaiming easier and helps keep your screens in good shape. For ideas that make the whole workflow smoother, see tricks for screen printing.