Why tote bags are a good first project
Tote bags are flat, simple and forgiving. They have no sleeves or hoods to work around, canvas holds ink well, and a bold one- or two-colour design looks good on a natural background. They are also a popular product for small sellers, which makes them a good way to practise before moving to garments. If you are brand new to the craft, our overview of what screen printing is explains the basic parts of the process.
Choose the right bag
- Fibre. Cotton canvas or cotton twill is the easiest. It absorbs ink and tolerates heat. Our guide to fabrics that are not good for screen printing explains why synthetic and coated bags are harder.
- Weight. Heavier canvas absorbs more ink and has a coarser weave, while lighter cotton gives a smoother surface for finer detail.
- Construction. Look for a bag with a flat printing area and no pockets or thick seams in the middle of where the design will sit.
- Handles and lining. Some totes have nylon or polyester straps, plastic trims or coated linings. These can melt or warp if you heat the whole bag, so check the label.
- Colour. Natural or white canvas is the simplest. Dark bags need more opaque ink (see below).
What you need
- A tote bag, ideally a few spares for test prints
- A screen with your stencil, plus a squeegee that fits inside the screen with a little room on each side
- Textile ink suited to canvas: water-based fabric ink or plastisol, depending on your setup and the ink’s instructions
- A hinge clamp or press, or a flat board with the screen taped down
- A piece of thick cardboard or a printing board that fits inside the bag
- Painter’s tape or light adhesive to keep the bag flat
- A heat source for curing: iron, heat press or heat gun, according to the ink
- Parchment paper or a pressing cloth
- A lint roller
Prepare the bag
- Pre-wash and dry the bag if the ink maker recommends it. This removes sizing and reduces shrinkage after printing. Skip fabric softener.
- Iron it flat. Wrinkles lead to uneven prints.
- Roll off lint with a lint roller.
- Slide a board or thick cardboard inside so the front is firm and flat and ink cannot reach the back layer. A sheet of paper over the board can catch bleed-through.
- Smooth and secure the bag. Tape the edges down or use a light adhesive on the board so the bag does not shift when the screen lifts.
Step by step
- Position the design. Many people place the design a few inches below the top edge and centred. Avoid seams and thick folds. Mark the centre with a small piece of tape or a light pencil mark, then line the screen against it.
- Set the off-contact. Raise the screen slightly above the bag so the mesh peels away cleanly. Hinge clamps help.
- Add ink and flood. Put a line of ink above the image, then spread a thin layer lightly across the stencil.
- Pull the squeegee. Use firm, even pressure in one stroke. Canvas often soaks up more ink than a T-shirt, so you may need a second pass for solid coverage. Keep the screen down for the second pass, or use a press so alignment stays the same.
- Lift straight up. Check the print, and if you see gaps, make a note for the next one.
- Let it dry or flash it. Water-based inks may dry quickly on the screen, so keep an eye on the mesh and clean when you finish.
- Cure the print. Follow the ink maker’s instructions, as time and temperature depend on the ink.
Curing and heat cautions
Most textile inks must be heated to become wash-resistant. Typical options are an iron with a pressing cloth, a heat press, or a heat gun. For a home iron, keep the iron moving over the print, use a cloth between iron and ink, and give the whole print area the recommended time. Cotton canvas can usually handle the heat. Nylon straps, synthetic linings and plastic parts may not, so keep the heat on the printed area only and test on an inconspicuous section. Always follow the ink maker’s instructions. If unsure, test on a spare bag first.
Dark and coloured canvas
Light inks tend to look dull or transparent on dark fabric, so for dark bags choose an opaque ink made for dark fabrics, or print a white base layer first and then the colour on top. This takes more screens and careful registration. For beginners, natural, white or light-coloured bags give more predictable results. See our cost guide for a sense of how extra colours add to the price.
Care instructions for the finished bag
- Wait for the ink to fully cure, and ideally leave it for a day or more before washing, if the ink maker suggests this.
- Wash inside out in cool water on a gentle cycle, and avoid bleach.
- Air-dry if possible, and avoid ironing directly on the print.
- Spot clean rather than washing often.
Troubleshooting
- Patchy ink. Use a second pass, more ink or a lower mesh count, and check the bag is flat.
- Ink bleeding at the edges. Use less ink, lighter pressure or a thicker ink.
- Print cracks. The ink film is too thick or was undercured, or the bag stretches too much. Print a thinner layer and recheck the cure.
- Back of the bag marked. Place a board and paper inside and check for ink leaks along tape lines.
- Print peels after washing. The ink probably did not cure fully. Review the time and temperature.
For a similar project on an unusual material, see our guide to screen printing on hessian and burlap.