What to Print On

How to Screen Print Posters: Paper, Ink and Registration Tips

Print posters at home with the right paper, ink and mesh. Learn artwork separations, registration, off-contact setup, drying and fixing common problems.

On this page
  1. What makes poster printing different from shirts
  2. Choose your paper
  3. Choose ink and mesh
  4. Prepare the artwork and separations
  5. Make and set up the screen
  6. Registration tips
  7. Print step by step
  8. Dry and flatten the prints
  9. Editioning and finishing
  10. Troubleshooting

What makes poster printing different from shirts

Posters are one of the classic uses of screen printing, and the technique is close to printing on fabric, with several differences:

  • Paper does not absorb ink the way cotton does, so the ink sits on the surface and needs to dry or cure differently.
  • You typically want exact alignment between colours, because even a small shift shows on a flat sheet.
  • Paper can curl, cockle or tear, so handling and drying matter.
  • You will usually use inks formulated for paper, not textile inks.

If you are new to the craft, our overview of screen printing covers the basics of screens, stencils and squeegees.

Choose your paper

Pick a paper that is heavy, stable and made for printing or art. Thin copy paper tends to wrinkle and warp with wet ink. Heavier cover-weight or printmaking paper handles the pressure and moisture better. Smooth or lightly textured surfaces are easiest, and very rough papers can cause patchy coverage.

Consider:

  • Weight. Heavier sheets (often sold in pounds or gsm, with higher numbers meaning thicker) resist curling.
  • Finish. Uncoated or lightly coated stocks usually take screen printing ink well. Very glossy coated stocks can be slow to dry.
  • Size. Choose a sheet size that fits comfortably inside your screen with room around the image.
  • Spares. Buy extra sheets for test prints and mistakes.

Always test a sheet from the same batch with your ink before you commit to the run.

Choose ink and mesh

  • Ink. Water-based screen printing inks made for paper are common for home work and easy to clean up. Other options include acrylic-based and oil-based paper inks. Check that the ink is suitable for paper and for screen printing, and follow the maker’s guidance on drying.
  • Mesh count. A medium-to-fine mesh, often in the 110 to 230 range, is typical for paper work. Lower counts lay down more ink for bold flat colour, higher counts hold finer detail. Choose based on your artwork and test.
  • Squeegee. A medium-hardness squeegee with a sharp, straight edge helps produce even coverage.

Prepare the artwork and separations

Each colour in the poster needs its own screen, so your artwork must be separated into one black-and-white layer per ink colour.

  1. Start with clean artwork. Vector artwork scales cleanly. If you are working from a raster image, make sure it has enough resolution for the final print size.
  2. Create one layer per colour. Assign each colour to its own layer, and output each layer as solid black on a clear or white background.
  3. Add registration marks. Place small identical marks, such as crosshairs, in the margins of every layer so you can align them.
  4. Consider trapping. A tiny overlap between adjacent colours stops hairline gaps appearing if there is a slight misalignment. Overlaps can also mix colours if inks are transparent, so plan accordingly.
  5. Avoid very fine lines. Hairlines and tiny text can clog or disappear. Thicken them if needed.
  6. Print the positives. Use a printer that gives dense black output on transparency film, or have them printed at a shop.

Make and set up the screen

  1. Degrease and dry the screen.
  2. Coat it with photo emulsion in low light and dry it horizontally in the dark.
  3. Tape the film positive to the screen with the artwork reading the right way round when viewed from the side the paper will touch, then expose it according to your light and emulsion instructions.
  4. Wash out the design with water, let the screen dry and tape off the edges around the image so ink cannot leak.
  5. Mount the screen in hinge clamps on a flat board. Hinge clamps are strongly recommended for posters because they hold the screen in the same place every time.
  6. Set the off-contact. Raise the screen slightly above the paper, using spacers such as coins or small folded cardboard, so that the mesh snaps back after each pull. A small gap, often an eighth of an inch or so, is a common starting point, though your frame and mesh may need a different amount.

Registration tips

Registration is the hardest and most important part of poster printing.

  • Make paper guides. Tape small pieces of card or thin plastic to the board at two edges (or an L-shape in a corner), so each sheet slides into the same spot.
  • Use a test sheet. Print the first screen on a scrap, then lay it under the next screen to check alignment before you print the real thing.
  • Do not move the hinge clamps between sheets. If you must move them, trace their position.
  • Hold the paper steady. A light spray of repositionable adhesive on the board stops paper sticking to the screen and lifting.
  • Use registration marks on every layer, then trim them away or place them outside the final image area.
  • Print the same way each time. Pull in one direction with similar pressure for every sheet.
  1. Place a sheet against the paper guides.
  2. Lower the screen and add a bead of ink above the image area.
  3. Gently flood the image by pulling a thin layer of ink across the mesh without pressing through, so the open areas are filled.
  4. Place the squeegee behind the ink at roughly a 45-degree angle and pull it firmly across in one smooth stroke.
  5. Lift the screen, remove the sheet and place it flat on a drying rack or a clean surface.
  6. Repeat for the whole run, flooding between prints so the ink does not dry in the mesh.
  7. When the colour is finished, wash the screen straight away so ink does not dry in the mesh, and let the prints dry fully before you print the next colour.

When printing several colours, many printers start with the lightest or most transparent colour and move to darker ones, but this depends on your design. Let each layer dry well before the next one so it does not lift or smear.

Dry and flatten the prints

Hang prints on a drying line or use a flat drying rack with space between each sheet. Fan-assisted air can speed things up. If the paper curls, weigh it down gently once it is fully dry, or press it under heavy books. Be careful with a heat gun or flash unit, since paper can cockle and some inks may blister.

Editioning and finishing

If you are making a limited run, the traditional approach is to number each print in pencil as a fraction (for example 7/50), sign it, and keep a few proofs aside. Trim registration marks if needed and store prints flat in acid-free paper if you want to keep them. For a bit of context about how screen-printed art is valued, see what screen printing is and how it works.

Troubleshooting

  • Prints look blurry. Check the off-contact gap and artwork resolution, and reduce pressure.
  • Ink spreads or bleeds. Use less ink, a thicker ink, or a finer mesh.
  • Colours are misaligned. Re-check the paper guides, hinge clamps and registration marks.
  • Streaks. Flood the screen more evenly and keep the squeegee edge clean and straight.
  • Mesh clogs. Wipe the screen between pulls, or add a retarder if your ink allows it.
  • Paper sticks to the screen. Use a little more adhesive on the board and a bit more off-contact.

The complete guide to what to print on

What Is Screen Printing? History, Process and Best Uses
Read the guide

Keep exploring

Guides from other topics

All topics →