What to Print On

How to Screen Print Large Fabric and Sarees at Home

Print fabric lengths and sarees that are bigger than your screen by repeating a pattern along a long table. Covers fabric choice, registration, ink and curing.

On this page
  1. The core problem: the fabric is bigger than the screen
  2. Choose the right fabric
  3. Set up a long printing table
  4. Plan the repeat and registration
  5. Choose ink and mesh
  6. Step by step: printing a long length
  7. Printing a saree
  8. Curing and aftercare
  9. Common problems
  10. Screen printing or DTF for large fabric?
  11. Can you take screen printing off fabric?

The core problem: the fabric is bigger than the screen

Most home screens are small, but a saree is roughly five to six metres long and a bolt of yardage can be longer still. Printing these does not mean using an enormous screen. Instead, you print the design in repeats along the length of the cloth, moving the screen (or the cloth) after each pull. Commercial textile printers use long flat tables for exactly this reason, and a scaled-down version works at home.

The method rewards patience and planning more than expensive equipment. A simple, repeatable motif is far easier than a single large picture.

Choose the right fabric

  • Cotton and cotton blends are the easiest. They absorb ink well and handle the heat that some inks need. Our guide to fabrics that are not good for screen printing explains why.
  • Linen and fine cotton voile can work well, but their weave affects fine detail.
  • Silk, georgette, chiffon and other delicate or sheer saree fabrics are harder. Ink can bleed along the fibres, and heat can damage them. If you want to try, look for inks recommended for silk or sheer fabrics, keep a very light touch and test on a spare piece or an offcut.
  • Synthetics such as polyester or nylon need special inks and careful curing.

Wash and iron the cloth before you start. This removes sizing and finishes, pre-shrinks the fabric and helps the ink grip. Do not use fabric softener.

Set up a long printing table

You need a flat, firm and clean surface at least as long as the section of fabric you plan to print at once.

  • A long table or several tables pushed together, with a smooth top. Any gaps or height differences will show up in the print.
  • A thin layer of padding, such as a blanket covered with a smooth sheet, can help the print transfer evenly. Keep it taut so it does not shift.
  • Hold the fabric flat. Many printers use a light spray adhesive or masking tape at the edges. Pins at the ends work for fabrics that tolerate holes. Choose a method that does not mark your cloth.
  • Put clean paper or plastic beneath the end of the fabric you are not printing, so wet ink does not touch the rest.

Plan the repeat and registration

  1. Measure the cloth and decide how wide and long the finished pattern will be.
  2. Design a repeat unit that fits in your screen, with a clear way to line up each placement, such as a small registration mark or a notch in the corner of the image.
  3. Mark the fabric. Draw faint guide lines with chalk or a water-erasable fabric pen, or lay a straight edge along the table and use it as a stop.
  4. Make stops for the screen. Taped blocks or clamps at the table edge help you position the screen in the same place each time. Hinge clamps can be moved, but you must mark the positions.
  5. Avoid overlap. Leave a tiny gap between repeats unless you are deliberately creating a continuous pattern. For continuous patterns, design the artwork so the edges match, and test it on paper first.

Choose ink and mesh

  • Water-based textile inks or fabric pigment inks are a common choice for home printers and give a softer feel. Follow the manufacturer’s instructions for heat setting.
  • Plastisol is durable but needs a higher cure temperature, which may not suit delicate cloth.
  • A medium mesh count works for bold shapes and block prints. Finer mesh holds more detail but deposits less ink. Test on a scrap.

Step by step: printing a long length

  1. Lay the cloth smooth and secure it. Mark your first position.
  2. Place the screen at the start line using your stops or guides.
  3. Add a line of ink, flood the screen lightly, then pull the squeegee in one smooth stroke with even pressure.
  4. Lift the screen straight up. Check the print, then lay a clean sheet under the ink-covered underside of the screen if you must set it down.
  5. Move to the next marked position and repeat. Many printers print every other repeat first, let them dry, then fill in the gaps so the screen never sits on wet ink.
  6. Clean the underside of the screen from time to time to avoid smudges.
  7. Allow the whole length to dry flat or hang it carefully, then cure it according to the ink maker’s instructions.

Printing a saree

A saree is usually made up of a body, a decorative border and a pallu (the end piece). Plan these in sections:

  • Work out which parts you want printed. Many people print the body with a small repeating motif and leave the border plain, or the reverse.
  • Treat each section as its own mini-project, with its own registration marks.
  • Lay the saree in folds only if you can keep the printing area completely flat and the ink away from the folds.
  • Choose a pattern you can forgive. Small variations between repeats look handmade and are part of the charm of block-style prints.
  • If the fabric is silk or another delicate weave, test the whole process on an offcut first, including washing and drying.

Curing and aftercare

Cure the print according to the ink instructions. For many water-based textile inks, this means ironing on the reverse side or the printed side through a pressing cloth, using a temperature the fabric can safely take. Do not overheat delicate cloth. Wait for the recommended time before washing, then wash gently with cool water, and avoid harsh scrubbing for the first few washes. Test one swatch first.

Common problems

  • Misaligned repeats. Use more marks or a physical stop, and print more slowly.
  • Smudges from the screen. Let each print dry before the screen sits over it, or print alternating repeats.
  • Bleeding edges. Use less ink, lighter pressure or a finer mesh.
  • Ink soaking through. Place an absorbent layer under thin fabric and use a thinner coat.
  • Stiff prints. Apply thinner coats or try a softer ink formulation.

Screen printing or DTF for large fabric?

DTF (direct to film) transfers are convenient for small, full-colour designs, but covering metres of cloth with them is cumbersome and expensive. Screen printing a repeat pattern is usually better suited to long lengths and fabric you want to feel soft. For small items or one-off photographic images, DTF may be easier. Our overview of screen printing discusses when each method makes sense, and our cost guide looks at how the budget compares.

Can you take screen printing off fabric?

Once ink has been properly cured, it is difficult to remove completely, and attempts can damage the cloth. If the print is still wet, rinsing may help. For cured prints, test any remover on a hidden spot and expect that the fabric may be marked. It is better to test your design on a scrap before committing to the final cloth.

The complete guide to what to print on

What Is Screen Printing? History, Process and Best Uses
Read the guide

Keep exploring

Guides from other topics

All topics →