Ghosting vs blur: which do you have?
These two problems look similar but have different causes:
- Ghosting is a faint second image or shadow, often offset in one direction. It usually means the paper moved, or the dye transferred again in a slightly different position.
- Blur is a generally soft or fuzzy image. It can come from the print file, the printer, too much ink, moisture, or the press, rather than from movement.
Working out which you have saves time. If the edges show a clear duplicate outline, think movement. If everything looks soft, including areas the paper never moved over, look at the file, printer and ink first.
Why ghosting happens
Sublimation dye stays active while the blank is hot. If the paper shifts, lifts or is removed unevenly, dye can land in a second spot and make a double image. Common causes:
- Paper not secured. Without heat-resistant tape, the paper can slide when the press closes or opens.
- Moving the press while closing or opening. Swing-away and clamshell presses can drag the paper if you open them unevenly.
- Uneven or low pressure. Air pockets or partial contact give the paper room to move.
- Moisture. Water in the shirt or paper turns to steam and can lift the paper slightly.
- Slow or sloppy paper removal. Peel the paper cleanly and without sliding it. Follow your paper’s instructions on hot or warm peeling, as it varies.
- Large designs. Bigger transfers have more room to shift.
How to prevent ghosting
- Pre-press the shirt for a few seconds (commonly 3-10) to remove moisture and wrinkles.
- Tape the transfer down on several sides with heat-resistant tape. Some people also use a light repositionable adhesive spray made for sublimation.
- Use a transfer that fully covers the design area, with a margin of paper around the artwork, so edges don’t fold or lift.
- Keep the garment flat and smooth. Use a pressing mat or a clean surface under it.
- Use even, medium to firm pressure across the platen.
- Lift the press straight up and avoid sliding the transfer.
- Remove the paper cleanly and promptly, pulling it back in a single motion rather than dragging it.
- Keep paper dry. Store it flat in a sealed bag away from humidity. See how to choose sublimation paper for shirts, including notes on tacky papers some people use on stretchy or thin fabrics.
Why transfers come out blurry
Soft or fuzzy results often start before the press:
- Low-resolution artwork. A small image stretched to full size looks soft. Aim for roughly 300 DPI at the printed size.
- Too much ink or the wrong profile. Heavy ink can bleed at the edges. The wrong paper setting or color profile can have the same effect.
- Clogged or misaligned print heads. Banding and fuzzy edges can come from the printer, so run a nozzle check and, if your printer offers it, a head alignment.
- Low print quality setting. Use the highest quality setting for your paper.
- Wrong or damp paper. Moist or poorly matched paper can cause bleed.
- Poor contact in the press. Uneven pressure or wrinkles can leave areas soft.
- Too much heat or time can sometimes cause dye to spread.
Fixing blur at the printer
- Open the artwork at 100% size and check it is sharp. Replace it with a higher-resolution file if not.
- Run a nozzle check and clean heads as needed.
- Print at the highest quality setting with the correct paper type selected.
- Confirm that your color profile matches your printer, ink and paper.
- Print a test on the same paper and look at fine text before pressing.
- Let the print dry briefly before handling it so it doesn’t smear.
Fixing blur at the press
- Pre-press and lint-roll the shirt.
- Tape the transfer tight against the shirt.
- Check your temperature and time against the paper and blank instructions. See why sublimation colors look dull or faded for settings checks.
- Make sure pressure is even. If you only see blur in one part of the design, uneven pressure or a wrinkle is likely.
- Check for humidity in your workspace and in your paper and blanks.
Quick symptom table
| Symptom | Likely cause | Try |
|---|---|---|
| Faint duplicate outline | Paper shifted | Tape more securely, lift press straight up |
| Shadow on one side only | Paper moved on opening | Open smoothly, peel in one motion |
| Soft edges everywhere | Low resolution or heavy ink | Use sharper artwork, check profile |
| Fuzzy edges and banding | Clogged heads or alignment | Nozzle check, clean heads |
| Soft patches | Moisture or poor contact | Pre-press, check pressure |
| Mirrored or shifted text | Not mirrored or misplaced | Mirror, position carefully |
A checklist for the next press
- Artwork is high resolution and mirrored.
- Nozzle check is clean.
- Shirt is lint-rolled and pre-pressed.
- Transfer is taped on all sides.
- Settings match your paper and blank.
- Press is lifted straight up and paper removed cleanly.
If you are new to the whole process, review the steps in our beginner’s sublimation t-shirt tutorial.